systemd-stub, sd-stub, linuxx64.efi.stub, linuxia32.efi.stub, linuxaa64.efi.stub - A simple UEFI kernel boot stub
systemd-stub (stored in per-architecture files linuxx64.efi.stub, linuxia32.efi.stub, linuxaa64.efi.stub on disk) is a simple UEFI boot stub. An UEFI boot stub is attached to a Linux kernel binary image, and is a piece of code that runs in the UEFI firmware environment before transitioning into the Linux kernel environment. The UEFI boot stub ensures a Linux kernel is executable as regular UEFI binary, and is able to do various preparations before switching the system into the Linux world.
The UEFI boot stub looks for various resources for the kernel invocation inside the UEFI PE binary itself. This allows combining various resources inside a single PE binary image (usually called "Unified Kernel Image", or "UKI" for short), which may then be signed via UEFI SecureBoot as a whole, covering all individual resources at once. Specifically it may include:
If UEFI SecureBoot is enabled and the ".cmdline" section is present in the executed image, any attempts to override the kernel command line by passing one as invocation parameters to the EFI binary are ignored. Thus, in order to allow overriding the kernel command line, either disable UEFI SecureBoot, or don't include a kernel command line PE section in the kernel image file. If a command line is accepted via EFI invocation parameters to the EFI binary it is measured into TPM PCR 12 (if a TPM is present).
If a DeviceTree is embedded in the ".dtb" section, it replaces an existing DeviceTree in the corresponding EFI configuration table. systemd-stub will ask the firmware via the "EFI_DT_FIXUP_PROTOCOL" for hardware specific fixups to the DeviceTree.
The contents of seven of these eight PE sections are measured into TPM PCR 11, that is otherwise not used. Thus, it can be pre-calculated without too much effort. The ".pcrsig" section is not included in this PCR measurement, since it's supposed to contain signatures for the expected results for these measurements, i.e. of the outputs of the measurement operation, and thus cannot also be input to it.
When ".pcrsig" and/or ".pcrpkey" are present in a unified kernel image their contents are passed to the booted kernel in an synthetic initrd cpio archive that places them in the /.extra/tpm2-pcr-signature.json and /.extra/tpm2-pcr-public-key.pem files. Typically, a tmpfiles.d(5) line then ensures they are copied into /run/systemd/tpm2-pcr-signature.json and /run/systemd/tpm2-pcr-public-key.pem where they remain accessible even after the system transitions out of the initrd environment into the host file system. Tools such systemd-cryptsetup@.service(8), systemd-cryptenroll(1) and systemd-creds(1) will automatically use files present under these paths to unlock protected resources (encrypted storage or credentials) or bind encryption to booted kernels.
The systemd-stub UEFI boot stub automatically collects two types of auxiliary companion files optionally placed in drop-in directories on the same partition as the EFI binary, dynamically generates cpio initrd archives from them, and passes them to the kernel. Specifically:
These mechanisms may be used to parameterize and extend trusted (i.e. signed), immutable initrd images in a reasonably safe way: all data they contain is measured into TPM PCRs. On access they should be further validated: in case of the credentials case by encrypting/authenticating them via TPM, as exposed by systemd-creds encrypt -T (see systemd-creds(1) for details); in case of the system extension images by using signed Verity images.
TPM PCR NOTES
Note that when a unified kernel using systemd-stub is invoked the firmware will measure it as a whole to TPM PCR 4, covering all embedded resources, such as the stub code itself, the core kernel, the embedded initrd and kernel command line (see above for a full list).
Also note that the Linux kernel will measure all initrds it receives into TPM PCR 9. This means every type of initrd will be measured two or three times: the initrd embedded in the kernel image will be measured to PCR 4, PCR 9 and PCR 11; the initrd synthesized from credentials will be measured to both PCR 9 and PCR 12; the initrd synthesized from system extensions will be measured to both PCR 4 and PCR 9. Let's summarize the OS resources and the PCRs they are measured to:
Table 1. OS Resource PCR Summary
|OS Resource||Measurement PCR|
|systemd-stub code (the entry point of the unified PE binary)||4|
|Core kernel code (embedded in unified PE binary)||4 + 11|
|OS release information (embedded in the unified PE binary)||4 + 11|
|Main initrd (embedded in unified PE binary)||4 + 9 + 11|
|Default kernel command line (embedded in unified PE binary)||4 + 11|
|Overridden kernel command line||12|
|Boot splash (embedded in the unified PE binary)||4 + 11|
|TPM2 PCR signature JSON (embedded in unified PE binary, synthesized into initrd)||4 + 9|
|TPM2 PCR PEM public key (embedded in unified PE binary, synthesized into initrd)||4 + 9 + 11|
|Credentials (synthesized initrd from companion files)||9 + 12|
|System Extensions (synthesized initrd from companion files)||9 + 13|
The following EFI variables are defined, set and read by
systemd-stub, under the vendor UUID "4a67b082-0a4c-41cf-b6c7-440b29bb8c4f", for communication between the boot stub and the OS:
Note that some of the variables above may also be set by the boot loader. The stub will only set them if they aren't set already. Some of these variables are defined by the Boot Loader Interface.
The following resources are passed as initrd cpio archives to the booted kernel, and thus make up the initial file system hierarchy in the initrd execution environment:
Note that all these files are located in the "tmpfs" file system the kernel sets up for the initrd file hierarchy and are thus lost when the system transitions from the initrd execution environment into the host file system. If these resources shall be kept around over this transition they need to be copied to a place that survives the transition first, for example via a suitable tmpfiles.d(5) line. By default, this is done for the TPM2 PCR signature and public key files.
ASSEMBLING KERNEL IMAGES
In order to assemble a bootable Unified Kernel Image from various components as described above, use ukify(1).
systemd-boot(7), systemd.exec(5), systemd-creds(1), systemd-sysext(8), Boot Loader Specification, Boot Loader Interface, ukify(1), systemd-measure(1)
- Boot Loader Interface
- Boot Loader Specification