The following commands are understood:
list [PATTERN...]
Show a list of existing links and their status. If one or
more
PATTERNs are specified, only links matching one of them are shown.
If no further arguments are specified shows all links, otherwise just the
specified links. Produces output similar to:
IDX LINK TYPE OPERATIONAL SETUP
1 lo loopback carrier unmanaged
2 eth0 ether routable configured
3 virbr0 ether no-carrier unmanaged
4 virbr0-nic ether off unmanaged
4 links listed.
The operational status is one of the following:
missing
The device is missing.
Added in version 245.
off
The device is powered down.
Added in version 240.
no-carrier
The device is powered up, but does not yet have a
carrier.
Added in version 240.
dormant
The device has a carrier, but is not yet ready for normal
traffic.
Added in version 240.
degraded-carrier
One of the bonding or bridge slave network interfaces is
in off, no-carrier, or dormant state, and the master interface has no address.
Added in version 242.
carrier
The link has carrier, or for bond or bridge master, all
bonding or bridge slave network interfaces are enslaved to the master.
Added in version 240.
degraded
The link has carrier and addresses valid on the local
link configured. For bond or bridge master this means that not all slave
network interfaces have carrier but at least one does.
Added in version 240.
enslaved
The link has carrier and is enslaved to bond or bridge
master network interface.
Added in version 242.
routable
The link has carrier and routable address configured. For
bond or bridge master it is not necessary for all slave network interfaces to
have carrier, but at least one must.
Added in version 240.
The setup status is one of the following:
pending
systemd-udevd(8) is still processing the link, we
don't yet know if we will manage it.
Added in version 240.
initialized
systemd-udevd(8) has processed the link, but we
don't yet know if we will manage it.
Added in version 251.
configuring
Configuration for the link is being retrieved or the link
is being configured.
Added in version 240.
configured
Link has been configured successfully.
Added in version 240.
unmanaged
systemd-networkd is not handling the link.
Added in version 240.
failed
systemd-networkd failed to configure the link.
Added in version 240.
linger
The link is gone, but has not yet been dropped by
systemd-networkd.
Added in version 240.
Added in version 219.
status [PATTERN...]
Show information about the specified links: type, state,
kernel module driver, hardware and IP address, configured DNS servers, etc. If
one or more
PATTERNs are specified, only links matching one of them are
shown.
When no links are specified, an overall network status is shown.
Also see the option --all.
Produces output similar to:
● State: routable
Online state: online
Address: 10.193.76.5 on eth0
192.168.122.1 on virbr0
169.254.190.105 on eth0
fe80::5054:aa:bbbb:cccc on eth0
Gateway: 10.193.11.1 (CISCO SYSTEMS, INC.) on eth0
DNS: 8.8.8.8
8.8.4.4
In the overall network status, the online state depends on the
individual online state of all required links. Managed links are required
for online by default. In this case, the online state is one of the
following:
unknown
All links have unknown online status (i.e. there are no
required links).
Added in version 249.
offline
All required links are offline.
Added in version 249.
partial
Some, but not all, required links are online.
Added in version 249.
online
All required links are online.
Added in version 249.
Added in version 219.
lldp [PATTERN...]
Show discovered LLDP (Link Layer Discovery Protocol)
neighbors. If one or more
PATTERNs are specified only neighbors on
those interfaces are shown. Otherwise shows discovered neighbors on all
interfaces. Note that for this feature to work,
LLDP= must be turned on
for the specific interface, see
systemd.network(5) for details.
Produces output similar to:
LINK SYSTEM-NAME SYSTEM-DESCRIPTION CHASSIS-ID PORT-ID PORT-DESCRIPTION CAPS
enp0s25 GS1900 - 00:e0:4c:00:00:00 2 Port #2 ..b........
Capability Flags:
o - Other; p - Repeater; b - Bridge; w - WLAN Access Point; r - Router;
t - Telephone; d - DOCSIS cable device; a - Station; c - Customer VLAN;
s - Service VLAN, m - Two-port MAC Relay (TPMR)
1 neighbor(s) listed.
Added in version 219.
label
Show numerical address labels that can be used for
address selection. This is the same information that
ip-addrlabel(8)
shows. See
RFC 3484[1] for a discussion of address labels.
Produces output similar to:
Prefix/Prefixlen Label
::/0 1
fc00::/7 5
fec0::/10 11
2002::/16 2
3ffe::/16 12
2001:10::/28 7
2001::/32 6
::ffff:0.0.0.0/96 4
::/96 3
::1/128 0
Added in version 234.
delete DEVICE...
Deletes virtual netdevs. Takes interface name or index
number.
Added in version 243.
up DEVICE...
Bring devices up. Takes interface name or index number.
Added in version 246.
down DEVICE...
Bring devices down. Takes interface name or index number.
Added in version 246.
renew DEVICE...
Renew dynamic configurations e.g. addresses received from
DHCP server. Takes interface name or index number.
Added in version 244.
forcerenew DEVICE...
Send a FORCERENEW message to all connected clients,
triggering DHCP reconfiguration. Takes interface name or index number.
Added in version 246.
reconfigure DEVICE...
Reconfigure network interfaces. Takes interface name or
index number. Note that this does not reload .netdev or .network corresponding
to the specified interface. So, if you edit config files, it is necessary to
call
networkctl reload first to apply new settings.
Added in version 244.
reload
Reload .netdev and .network files. If a new .netdev file
is found, then the corresponding netdev is created. Note that even if an
existing .netdev is modified or removed,
systemd-networkd does not
update or remove the netdev. If a new, modified or removed .network file is
found, then all interfaces which match the file are reconfigured.
Added in version 244.
edit FILE|@DEVICE...
Edit network configuration files, which include .network,
.netdev, and .link files. If no network config file matching the given name is
found, a new one will be created under /etc/ or /run/, depending on whether
--runtime is specified. Specially, if the name is prefixed by
"@", it will be treated as a network interface, and editing will be
performed on the network config files associated with it. Additionally, the
interface name can be suffixed with ":network" (default) or
":link", in order to choose the type of network config to operate
on.
If --drop-in= is specified, edit the drop-in file instead
of the main configuration file. Unless --no-reload is specified,
systemd-networkd will be reloaded after the edit of the .network or
.netdev files finishes. The same applies for .link files and
systemd-udevd(8). Note that the changed link settings are not
automatically applied after reloading. To achieve that, trigger uevents for
the corresponding interface. Refer to systemd.link(5) for more
information.
Added in version 254.
cat [FILE|@DEVICE...]
Show network configuration files. This command honors the
"@" prefix in the same way as
edit. When no argument is
specified,
networkd.conf(5) and its drop-in files will be shown.
Added in version 254.
mask FILE...
Mask network configuration files, which include .network,
.netdev, and .link files. A symlink of the given name will be created under
/etc/ or /run/, depending on whether
--runtime is specified, that
points to /dev/null. If a non-empty config file with the specified name exists
under the target directory or a directory with higher priority (e.g.
--runtime is used while an existing config resides in /etc/), the
operation is aborted.
This command honors --no-reload in the same way as
edit.
Added in version 256.
unmask FILE...
Unmask network configuration files, i.e. reverting the
effect of
mask. Note that this command operates regardless of the scope
of the directory, i.e.
--runtime is of no effect.
This command honors --no-reload in the same way as
edit and mask.
Added in version 256.
persistent-storage BOOL
Notify systemd-networkd.service that the persistent
storage for the service is ready. This is called by
systemd-networkd-persistent-storage.service. Usually, this command should not
be called manually by users or administrators.
Added in version 256.
The following options are understood:
-a --all
Show all links with
status.
Added in version 219.
-s --stats
Show link statistics with
status.
Added in version 243.
-l, --full
Do not ellipsize the output.
Added in version 245.
-n, --lines=
When used with
status, controls the number of
journal lines to show, counting from the most recent ones. Takes a positive
integer argument. Defaults to 10.
Added in version 245.
--drop-in=NAME
When used with
edit, edit the drop-in file
NAME instead of the main configuration file.
Added in version 254.
--no-reload
--runtime
When used with
edit or
mask, operate on the
file under /run/ instead of /etc/.
Added in version 256.
--json=MODE
Shows output formatted as JSON. Expects one of
"short" (for the shortest possible output without any redundant
whitespace or line breaks), "pretty" (for a pretty version of the
same, with indentation and line breaks) or "off" (to turn off JSON
output, the default).
-h, --help
Print a short help text and exit.
--version
Print a short version string and exit.
--no-legend
Do not print the legend, i.e. column headers and the
footer with hints.
--no-pager
Do not pipe output into a pager.