SYSTEMD-SLEEP.CONF(5) | systemd-sleep.conf | SYSTEMD-SLEEP.CONF(5) |
NAME
systemd-sleep.conf, sleep.conf.d - Suspend and hibernation configuration file
SYNOPSIS
DESCRIPTION
systemd supports four general power-saving modes:
suspend
Added in version 203.
hibernate
Added in version 203.
hybrid-sleep
Added in version 203.
suspend-then-hibernate
If the system has no battery, it would be hibernated after HibernateDelaySec= has passed. If not set, then defaults to "2h".
If the system has battery and HibernateDelaySec= is not set, low-battery alarms (ACPI _BTP) are tried first for detecting battery percentage and wake up the system for hibernation. If not available, or HibernateDelaySec= is set, the system would regularly wake up to check the time and detect the battery percentage/discharging rate. The rate is used to schedule the next detection. If that is also not available, SuspendEstimationSec= is used as last resort.
Added in version 239.
Settings in these files determine what strings will be written to /sys/power/disk and /sys/power/state by systemd-sleep(8) when systemd(1) attempts to suspend or hibernate the machine. See systemd.syntax(7) for a general description of the syntax.
CONFIGURATION DIRECTORIES AND PRECEDENCE
The default configuration is set during compilation, so configuration is only needed when it is necessary to deviate from those defaults. The main configuration file is loaded from one of the listed directories in order of priority, only the first file found is used: /etc/systemd/, /run/systemd/, /usr/local/lib/systemd/ [1], /usr/lib/systemd/. The vendor version of the file contains commented out entries showing the defaults as a guide to the administrator. Local overrides can also be created by creating drop-ins, as described below. The main configuration file can also be edited for this purpose (or a copy in /etc/ if it's shipped under /usr/), however using drop-ins for local configuration is recommended over modifications to the main configuration file.
In addition to the main configuration file, drop-in configuration snippets are read from /usr/lib/systemd/*.conf.d/, /usr/local/lib/systemd/*.conf.d/, and /etc/systemd/*.conf.d/. Those drop-ins have higher precedence and override the main configuration file. Files in the *.conf.d/ configuration subdirectories are sorted by their filename in lexicographic order, regardless of in which of the subdirectories they reside. When multiple files specify the same option, for options which accept just a single value, the entry in the file sorted last takes precedence, and for options which accept a list of values, entries are collected as they occur in the sorted files.
When packages need to customize the configuration, they can install drop-ins under /usr/. Files in /etc/ are reserved for the local administrator, who may use this logic to override the configuration files installed by vendor packages. Drop-ins have to be used to override package drop-ins, since the main configuration file has lower precedence. It is recommended to prefix all filenames in those subdirectories with a two-digit number and a dash, to simplify the ordering. This also defines a concept of drop-in priorities to allow OS vendors to ship drop-ins within a specific range lower than the range used by users. This should lower the risk of package drop-ins overriding accidentally drop-ins defined by users. It is recommended to use the range 10-40 for drop-ins in /usr/ and the range 60-90 for drop-ins in /etc/ and /run/, to make sure that local and transient drop-ins take priority over drop-ins shipped by the OS vendor.
To disable a configuration file supplied by the vendor, the recommended way is to place a symlink to /dev/null in the configuration directory in /etc/, with the same filename as the vendor configuration file.
OPTIONS
The following options can be configured in the [Sleep] section of /etc/systemd/sleep.conf or a sleep.conf.d file:
AllowSuspend=, AllowHibernation=, AllowHybridSleep=, AllowSuspendThenHibernate=
If AllowHibernation=no or AllowSuspend=no is used, this implies AllowSuspendThenHibernate=no and AllowHybridSleep=no, since those methods use both suspend and hibernation internally. AllowSuspendThenHibernate=yes and AllowHybridSleep=yes can be used to override and enable those specific modes.
Added in version 240.
SuspendState=
The allowed set of values is determined by the kernel and is shown in the file itself (use cat /sys/power/state to display). See Basic sysfs Interfaces for System Suspend and Hibernation[2] for more details.
systemd-suspend-then-hibernate.service(8) uses this value when suspending.
Added in version 203.
HibernateMode=
The allowed set of values is determined by the kernel and is shown in the file itself (use cat /sys/power/disk to display). See the kernel documentation page Basic sysfs Interfaces for System Suspend and Hibernation[2] for more details.
systemd-suspend-then-hibernate.service(8) uses the value of HibernateMode= when hibernating.
Added in version 203.
MemorySleepMode=
The allowed set of values is determined by the kernel and is shown in the file itself (use cat /sys/power/mem_sleep to display). See the kernel documentation page Basic sysfs Interfaces for System Suspend and Hibernation[2] for more details.
Added in version 256.
HibernateDelaySec=
Added in version 239.
SuspendEstimationSec=
Added in version 253.
EXAMPLE: FREEZE
Example: to exploit the “freeze” mode added in Linux 3.9, one can use systemctl suspend with
[Sleep] SuspendState=freeze
SEE ALSO
systemd-sleep(8), systemd-suspend.service(8), systemd-hibernate.service(8), systemd-hybrid-sleep.service(8), systemd-suspend-then-hibernate.service(8), systemd(1), systemd.directives(7)
NOTES
- 1.
- 💣💥🧨💥💥💣 Please note that those configuration files must be available at all times. If /usr/local/ is a separate partition, it may not be available during early boot, and must not be used for configuration.
- 2.
- Basic sysfs Interfaces for System Suspend and Hibernation
systemd 256.8 |