.\" Copyright (c) 2006 Andrew Morton .\" and Copyright 2006 Michael Kerrisk .\" .\" SPDX-License-Identifier: Linux-man-pages-copyleft .\" .\" 2006-07-05 Initial creation, Michael Kerrisk based on .\" Andrew Morton's comments in fs/sync.c .\" 2010-10-09, mtk, Document sync_file_range2() .\" .TH sync_file_range 2 2024-05-02 "Linux man-pages 6.9.1" .SH NAME sync_file_range \- sync a file segment with disk .SH LIBRARY Standard C library .RI ( libc ", " \-lc ) .SH SYNOPSIS .nf .BR "#define _GNU_SOURCE" " /* See feature_test_macros(7) */" .B #define _FILE_OFFSET_BITS 64 .B #include .P .BI "int sync_file_range(int " fd ", off_t " offset ", off_t " nbytes , .BI " unsigned int " flags ); .fi .SH DESCRIPTION .BR sync_file_range () permits fine control when synchronizing the open file referred to by the file descriptor .I fd with disk. .P .I offset is the starting byte of the file range to be synchronized. .I nbytes specifies the length of the range to be synchronized, in bytes; if .I nbytes is zero, then all bytes from .I offset through to the end of file are synchronized. Synchronization is in units of the system page size: .I offset is rounded down to a page boundary; .I (offset+nbytes\-1) is rounded up to a page boundary. .P The .I flags bit-mask argument can include any of the following values: .TP .B SYNC_FILE_RANGE_WAIT_BEFORE Wait upon write-out of all pages in the specified range that have already been submitted to the device driver for write-out before performing any write. .TP .B SYNC_FILE_RANGE_WRITE Initiate write-out of all dirty pages in the specified range which are not presently submitted write-out. Note that even this may block if you attempt to write more than request queue size. .TP .B SYNC_FILE_RANGE_WAIT_AFTER Wait upon write-out of all pages in the range after performing any write. .P Specifying .I flags as 0 is permitted, as a no-op. .SS Warning This system call is extremely dangerous and should not be used in portable programs. None of these operations writes out the file's metadata. Therefore, unless the application is strictly performing overwrites of already-instantiated disk blocks, there are no guarantees that the data will be available after a crash. There is no user interface to know if a write is purely an overwrite. On filesystems using copy-on-write semantics (e.g., .IR btrfs ) an overwrite of existing allocated blocks is impossible. When writing into preallocated space, many filesystems also require calls into the block allocator, which this system call does not sync out to disk. This system call does not flush disk write caches and thus does not provide any data integrity on systems with volatile disk write caches. .SS Some details .B SYNC_FILE_RANGE_WAIT_BEFORE and .B SYNC_FILE_RANGE_WAIT_AFTER will detect any I/O errors or .B ENOSPC conditions and will return these to the caller. .P Useful combinations of the .I flags bits are: .TP .B SYNC_FILE_RANGE_WAIT_BEFORE | SYNC_FILE_RANGE_WRITE Ensures that all pages in the specified range which were dirty when .BR sync_file_range () was called are placed under write-out. This is a start-write-for-data-integrity operation. .TP .B SYNC_FILE_RANGE_WRITE Start write-out of all dirty pages in the specified range which are not presently under write-out. This is an asynchronous flush-to-disk operation. This is not suitable for data integrity operations. .TP .BR SYNC_FILE_RANGE_WAIT_BEFORE " (or " SYNC_FILE_RANGE_WAIT_AFTER ) Wait for completion of write-out of all pages in the specified range. This can be used after an earlier .B SYNC_FILE_RANGE_WAIT_BEFORE | SYNC_FILE_RANGE_WRITE operation to wait for completion of that operation, and obtain its result. .TP .B SYNC_FILE_RANGE_WAIT_BEFORE | SYNC_FILE_RANGE_WRITE | \ SYNC_FILE_RANGE_WAIT_AFTER This is a write-for-data-integrity operation that will ensure that all pages in the specified range which were dirty when .BR sync_file_range () was called are committed to disk. .SH RETURN VALUE On success, .BR sync_file_range () returns 0; on failure \-1 is returned and .I errno is set to indicate the error. .SH ERRORS .TP .B EBADF .I fd is not a valid file descriptor. .TP .B EINVAL .I flags specifies an invalid bit; or .I offset or .I nbytes is invalid. .TP .B EIO I/O error. .TP .B ENOMEM Out of memory. .TP .B ENOSPC Out of disk space. .TP .B ESPIPE .I fd refers to something other than a regular file, a block device, or a directory. .SH VERSIONS .SS sync_file_range2() Some architectures (e.g., PowerPC, ARM) need 64-bit arguments to be aligned in a suitable pair of registers. .\" See kernel commit edd5cd4a9424f22b0fa08bef5e299d41befd5622 On such architectures, the call signature of .BR sync_file_range () shown in the SYNOPSIS would force a register to be wasted as padding between the .I fd and .I offset arguments. (See .BR syscall (2) for details.) Therefore, these architectures define a different system call that orders the arguments suitably: .P .in +4n .EX .BI "int sync_file_range2(int " fd ", unsigned int " flags , .BI " off_t " offset ", off_t " nbytes ); .EE .in .P The behavior of this system call is otherwise exactly the same as .BR sync_file_range (). .SH STANDARDS Linux. .SH HISTORY Linux 2.6.17. .SS sync_file_range2() A system call with this signature first appeared on the ARM architecture in Linux 2.6.20, with the name .BR arm_sync_file_range (). It was renamed in Linux 2.6.22, when the analogous system call was added for PowerPC. On architectures where glibc support is provided, glibc transparently wraps .BR sync_file_range2 () under the name .BR sync_file_range (). .SH NOTES .B _FILE_OFFSET_BITS should be defined to be 64 in code that takes the address of .BR sync_file_range , if the code is intended to be portable to traditional 32-bit x86 and ARM platforms where .BR off_t 's width defaults to 32 bits. .SH SEE ALSO .BR fdatasync (2), .BR fsync (2), .BR msync (2), .BR sync (2)