NVME-CONFIG-STATUS(1) NVMe Manual NVME-CONFIG-STATUS(1) NAME nvme-config-status - Report legacy NVMe-oF config.json/discovery.conf conversion status SYNOPSIS nvme [] config status DESCRIPTION Reports the on-disk state of the legacy pre-3.0 configuration files, /etc/nvme/config.json and /etc/nvme/discovery.conf, and of the *.converted marker nvme config convert leaves next to each one it converts. This command never modifies or converts anything; it only reports state. One line is printed for each legacy file that has something to report: o present, not yet converted -- the file exists and has never been converted. o present, already converted -- the file exists and a .converted marker (a symlink pointing back at the file itself, left in place deliberately so a rollback to a pre-INI installation still finds the original legacy file) confirms it was converted. Both the file and the marker can be deleted once rollback is no longer a concern. o not present (a stale marker exists) -- the file is gone but its .converted marker is still there, dangling. This is left over from an earlier conversion and is always safe to delete. A file with neither itself nor a marker present is silently skipped -- there is nothing to say about it. If this is true of both config.json and discovery.conf, a single no legacy configuration found line is printed instead of two silent files and no output at all. Because the marker is a symlink keyed on the file's path, not its content, a file that is deleted and later replaced by a different, never-converted file at the same path (for example, a package rollback followed by a reinstall) makes the marker resolve again even though the new file itself was never converted. This command does not try to detect that case -- when a file and a resolving marker are both present, it adds a note that the marker may be stale and the file's contents should be verified against the INI configuration, so a human can decide. Use nvme config convert if in doubt: converting an already-converted file is a safe no-op. OPTIONS GLOBAL OPTIONS The following options are defined at the top-level nvme command and are available to this subcommand: --dry-run Print the command that would be executed, but do not actually execute it. --no-ioctl-probing Disable probing for 64-bit IOCTL support. --no-retries Disable retry logic on transient errors. -o , --output-format= Set the reporting format to normal, tabular, 'json, or binary. Only one output format may be used at a time. --output-format-version= Select the output format version. Version 1 uses the original field naming, while version 2 (default) provides more consistent and script-friendly field names. --timeout= Set the timeout for the command in milliseconds. -v, --verbose Increase the level of detail in the output. May be specified multiple times to further increase verbosity. These options can also be set as machine-wide defaults in nvme-cli.conf(5). A command-line flag always overrides the file. EXIT STATUS Returns 0 if neither legacy file has anything to report. Returns a non-zero status if config.json or discovery.conf, or a .converted marker for either, is present -- regardless of which of the states listed above applies. Use the printed output, not the exit status, to tell those states apart. EXAMPLES o Check the system's legacy configuration state, config.json already converted and no discovery.conf ever present: # nvme config status /usr/local/etc/nvme/config.json: present, already converted (/usr/local/etc/nvme/config.json.converted exists) -- delete both once rollback is no longer a concern note: if /usr/local/etc/nvme/config.json was replaced after conversion (for example, a package rollback followed by reinstall), this marker may be stale; verify its contents against the INI configuration before deleting either file o Check a system that never had a legacy configuration: # nvme config status no legacy configuration found; nothing to convert SEE ALSO nvme-config-convert(1) nvme-config-show(1) nvme-config-validate(1) nvme-connect-all(1) nvme-discover(1) https://github.com/linux-nvme/nvme-cli/blob/master/libnvme/design/CONFIG.md NVME Part of the nvme-user suite NVMe 09/07/2026 NVME-CONFIG-STATUS(1)