|General Commands Manual
histretch - translating binary HINT files to ASCII files
histretch [options] [file]
Stretching converts a binary HINT file, usually with the extension .hnt, into an ASCII based HINT file, with the extension .hint.
The binary HINT file format - also called `short' format - is optimized for displaying HINT files. It can be parsed equally well in forward and backward direction to enable fast forward or backward navigation in the file.
The ASCII based HINT file format - also called `long' format - is optimized for readability. It can be edited using a text editor. Hence it allows simple modifications that would be difficult to achieve when using the binary format. It is also convenient when debugging.
The binary HINT file format is designed for on-screen reading of documents. Using a HINT viewer to display a HINT file, its content will dynamically adapt to the available display area. For complete information on the HINT file format and programs to view HINT files, see https://hint.userweb.mwn.de.
This version of histretch understands the following command line options:
- Write auxiliar files to disk using the localized path names as explained
in the FILES section below.
Use this option if you are stretching a HINT file that you later want to shrink back to its binary format unless you know that you have already all the auxiliary files contained in it.
- -d bitmask
- Sets HINT file debugging flags according to the bitmask. See the --help option for details.
- Force the replacement of existing auxiliary files. Use this option
together with the -g or -a option to make sure that already
exiting auxiliary files are replaced by the auxiliary files contained in
the HINT file.
WARNING: This is a dangerous option especially together with the -g option. Never use it on a HINT file of unknown origin. It will possibly replace any file on your machine you have write access to. If in doubt, don't use the -f option.
- Write auxiliar files to disk using the path names as stored in the HINT
file. This option is an alternative to the -a option and takes
precedence if given. If in doubt, don't use the -g option. If you
just want to stretch the HINT file, then edit it, and then shrink it back
to the binary format, you should use the -a option.
You may use this option if you are stretching a HINT file on the same machine and in the same directory where you have created the HINT file. Then all files will be copied to the location they came from in case they were deleted in the meantime.
If you are stretching a HINT file on one machine and the file was created on a different machine, histretch will try to copy an auxiliary file into the same directory that was used when the HINT file was created, provided that you have the necessary writing rights. This is probably where you want the auxiliary file assuming that both machines have the same directory structure.
WARNING: This is a dangerous option especially together with the -f option. Never use it on a HINT file of unknown origin. It can possibly write (and replace) any file on your machine where you have write access.
- Print help message and exit.
- Redirect standard error to a log file. The name of the log file is derived from the name of the input file replacing the extension .hnt by the extension .log.
- -o name
- Use name for the output file instead of deriving it from the name of the input file. Append the extension .hint if the name does not already has that extension.
- Enable the use of UTF8 character codes. Without this option, the output file is a pure ASCII file, because character codes outside the ASCII range are written using their numeric representation. With this option, the file will always represent printable characters using their UTF8 character codes. This might make the output file more readable if displayed using an UTF8 enabled program; but it might be less readable if displayed by a program that does not handle UTF8 characters properly. See also the -x option.
- Print version information and exit.
- Enable the use of hexadecimal character codes. Without this option, characters that are not represented using their character codes are represented using a decimal representation of the character code. With this option a hexadecimal representation is used. The range of character codes that have a numeric representation includes the non printable characters (character codes smaller than 32) and unless the -u option is given, the character codes with a value of 127 and above.
Binary HINT files must contain all resources necessary to display the file, for example font and image files. These files are called auxiliary files. ASCII HINT files contain only the path names of these files.
When creating a binary HINT file from an ASCII HINT file, it is necessary to find these files, read them, and include them in the binary output file. When creating an ASCII HINT file from a binary HINT file, it is convenient if these files can be extracted and written to the file system. To avoid clobbering arbitrary directories with files when extracting auxiliary files, it is possible to map the path names as stored in the HINT file to localized path names before writing or reading auxiliar files.
When computing a localized path name from a given path name, a distinction is made between global resources, like fonts, that are referenced by an absolute path name, and local resources, for example an image, that are referenced by a relative path name. The directory that starts the localized path name of the former has the extension .abs and for the latter the extension .rel is used. To keep auxiliary files in these subdirectories even if their path contains links to a parent directory, parent links `..' are replaced by `__' links to subdirectories.
For example, given an input file paper.hint, the global resources are stored in the paper.abs directory and local resources are stored in paper.rel. An absolute path like /usr/share/fonts/ will then map to the localized path paper.abs/usr/share/fonts/ and a relative path like ../image/img1.jpg will then map to the localized path paper.rel/__/image/img1.jpg.
This manual page is not meant to be exhaustive. The complete documentation can be found in HINT: The file format. This document is available as a book or in electronic form from the HINT project home page at https://hint.userweb.mwn.de. There you find additional software, most importantly viewers for HINT files, and further information.
histretch should compile on a large variety of machine architectures and operating systems. It is part of the TeX Live distribution.
|11 November 2021