mkfs.exfat(8) | System Manager's Manual | mkfs.exfat(8) |
NAME
mkfs.exfat - create an exFAT filesystem
SYNOPSIS
mkfs.exfat [ -b boundary_alignment ] [
-s sector_size ] [ -c cluster_size ] [ -f
] [ -h ] [ -L volume_label ] [ -U
volume_guid ] [ --pack-bitmap ] [ -v ] device
mkfs.exfat -V
DESCRIPTION
mkfs.exfat creates an exFAT filesystem by writing on a special file using the values found in the arguments of the command line. It is invoked automatically by mkfs(8) when it is given the -t exfat option.
As an example, to make a filesystem on the first partition on the first SCSI disk, use:
- mkfs.exfat /dev/sda1
OPTIONS
- -b, --boundary-align=alignment
- Specifies the alignment for the FAT and the start of the cluster heap. The
alignment argument is specified in bytes or may be specified with
m/M suffix for mebibytes or k/K suffix for
kibibytes and should be a power of two. Some media like SD cards need this
for optimal performance and endurance, in which case alignment
should be set to half of the card's native boundary unit size. If the
card's native boundary unit size is not known, refer to the following
table of boundary unit sizes recommended by the SD Card Association.
Card Capacity Range Cluster Size Boundary Unit ≤8 MiB 8 KiB 8 KiB >8 MiB ≤64 MiB 16 KiB 16 KiB >64 MiB ≤256 MiB 16 KiB 32 KiB >256 MiB ≤1 GiB 16 KiB 64 KiB >1 GiB ≤2 GiB 32 KiB 64 KiB >2 GiB ≤32 GiB 32 KiB 4 MiB >32 GiB ≤128 GiB 128 KiB 16 MiB >128 GiB ≤512 GiB 256 KiB 32 MiB >512 GiB ≤2 TiB 512 KiB 64 MiB - -s, --sector-size=size
- Specifies the sector size of the exFAT file system. The size argument is specified in bytes or may be specified with k/K suffix for kibibytes and must either 512, 1024, 2048 or 4096 bytes. The default value is the sector size reported by the device, or 512 bytes if the device sector size cannot be determined.
- -c, --cluster-size=size
- Specifies the cluster size of the exFAT file system. The size
argument is specified in bytes or may be specified with m/M
suffix for mebibytes or k/K suffix for kibibytes and must be
a power of two. The default value is described in the following table:
Card Capacity Range Cluster Size ≤256 MiB 4 KiB >256 MiB ≤32 GiB 32 KiB >32 GiB 128 KiB - -f, --full-format
- Performs a full format. This zeros the entire disk device while creating the exFAT filesystem.
- -h, --help
- Prints the help and exit.
- -L, --volume-label=label
- Specifies the volume label to be associated with the exFAT filesystem.
- -U, --volume-guid=guid
- Specifies the volume GUID to be associated with the exFAT filesystem. It can be given in the standard, hypenized UUID format like aaaabbbb-cccc-dddd-eeee-ffff00001111. Note: The volume GUID cannot be used to set the the 8-letter ID reported by blkid or used as the filesystem UUID in /etc/fstab.
- --pack-bitmap
- Attempts to relocate the exFAT allocation bitmap so that it ends at the alignment boundary immediately following the FAT rather than beginning at that boundary. This strictly violates the SD card specification but may improve performance and endurance on SD cards and other flash media not designed for use with exFAT by allowing file-system metadata updates to touch fewer flash allocation units. Furthermore, many SD cards and other flash devices specially optimize the allocation unit where the FAT resides so as to support tiny writes with reduced write amplification but expect only larger writes in subsequent allocation units — where the exFAT bitmap would be placed by default. Specifying --pack-bitmap attempts to avoid the potential problems associated with issuing many small writes to the bitmap by making it share an allocation unit with the FAT. If there is insufficient space for the bitmap there, then this option will have no effect, and the bitmap will be aligned at the boundary as by default.
- -q, --quiet
- Prints only error messages while creating the exFAT filesystem.
- -v, --verbose
- Prints verbose debugging information while creating the exFAT filesystem.
- -V, --version
- Prints the version number and exits.