BTRFSTUNE(8) BTRFS BTRFSTUNE(8)

btrfstune - tune various filesystem parameters

btrfstune [options] <device> [<device>...]

btrfstune can be used to enable, disable, or set various filesystem parameters. The filesystem must be unmounted.

The common use case is to enable features that were not enabled at mkfs time. Please make sure that you have kernel support for the features. You can find a complete list of features and kernel version of their introduction at Feature by version page. Also, the manual page mkfs.btrfs(8) contains more details about the features.

Some of the features could be also enabled on a mounted filesystem by other means. Please refer to the FILESYSTEM FEATURES in btrfs(5).

(since kernel 6.1)

Convert portions of extent tree that tracks block groups to a separate block group tree. This greatly reduces mount time. Can be also enabled at mkfs time.

(since kernel 6.1)

Convert block groups tracked in standalone block group tree back to extent tree and remove block-group-tree feature bit from the filesystem.

(since kernel 4.5)

Convert to free-space-tree feature (v2 of space cache).

Allow dangerous changes, e.g. clear the seeding flag or change fsid. Make sure that you are aware of the dangers.
(since kernel: 5.0)

change fsid stored as metadata_uuid to a randomly generated UUID, see also -U

(since kernel: 5.0)

change fsid stored as metadata_uuid to a given UUID, see also -U

The metadata_uuid is stored only in the superblock and is a backward incompatible change. The fsid in metadata blocks remains unchanged and is not overwritten, thus the whole operation is significantly faster than -U.

The new metadata_uuid can be used for mount by UUID and is also used to identify devices of a multi-device filesystem.

(since kernel: 3.14)

Enable no-holes feature (more efficient representation of file holes), enabled by mkfs feature no-holes.

(since kernel: 3.7)

Enable extended inode refs (hardlink limit per file in a directory is 65536), enabled by mkfs feature extref.

Enable seeding on a given device. Value 1 will enable seeding, 0 will disable it. A seeding filesystem is forced to be mounted read-only. A new device can be added to the filesystem and will capture all writes keeping the seeding device intact. See also section SEEDING DEVICE in btrfs(5).

WARNING:

Clearing the seeding flag on a device may be dangerous. If a previously-seeding device is changed, all filesystems that used that device will become unmountable. Setting the seeding flag back will not fix that.

A valid usecase is seeding device as a base image. Clear the seeding flag, update the filesystem and make it seeding again, provided that it's OK to throw away all filesystems built on top of the previous base.

Change fsid to a randomly generated UUID or continue previous fsid change operation in case it was interrupted.
Change fsid to UUID in all metadata blocks.

The UUID should be a 36 bytes string in printf(3) format %08x-%04x-%04x-%04x-%012x. If there is a previous unfinished fsid change, it will continue only if the UUID matches the unfinished one or if you use the option -u.

All metadata blocks are rewritten, this may take some time, but the final filesystem compatibility is unaffected, unlike -M.

WARNING:

Cancelling or interrupting a UUID change operation will make the filesystem temporarily unmountable. To fix it, rerun btrfstune -u and let it complete.
(since kernel: 3.10)

Enable skinny metadata extent refs (more efficient representation of extents), enabled by mkfs feature skinny-metadata.

All newly created extents will use the new representation. To completely switch the entire filesystem, run a full balance of the metadata. Please refer to btrfs-balance(8).

btrfstune returns 0 if no error happened, 1 otherwise.

This deprecated tool exists for historical reasons but is still in use today. Its functionality will be merged to the main tool, at which time btrfstune will be declared obsolete and scheduled for removal.

btrfs(5), btrfs-balance(8), mkfs.btrfs(8)

December 1, 2024 6.12